Woodworking engraving machine positioning

Woodworking engraving machine is one of the more commonly used engraving machines. It is widely used in wood carving. The following small series introduces the positioning of wood engraving machine for you briefly.

Positioning must first be from the fixed beginning of the data. The fixation here is not to say that the data is fastened with the splint, and the information is still correct. Use our carpenter carving machine to accurately align the data, install a straight knife on the spindle, then drop the tool onto the table, run along the side of the data, use a side of the data and a direct gap between the tools Come to find the information. Correct the data in the future. Then proceed to the next job to determine the workpiece origin of the data.

The determination of the X direction and the Y direction is the same method. Here we only say the X direction. First fine-tune the tool slowly to the left side of the data, and slowly roll the tool by hand until the tool just touches the data, then clear the left side of the X workpiece, and then lift the tool to the right. The same is to just touch the tool to the right side of the data, note the X workpiece coordinates at the moment. Then the general orientation of this value is the center of the data X direction. The Y direction is also the same. In this way, the center of the X and Y directions of the carpenter carving machine is determined, which is equivalent to the origin of the workpiece.

The selection of wooden doors is mainly solid wood, especially solid wood composite materials, which preserves the advantages of natural wood and avoids the disadvantages of easy deformation and cracking. The selection of materials is of course important, but in the manufacturing process, sophisticated. Traditional craft manufacturing processes have gradually been replaced by mechanical manufacturing. Carpenter carving machine has become the new favorite of wooden door manufacturing and has been favored by more and more wooden door manufacturers. First and foremost, as mechanized equipment, it is more efficient than manual manufacturing, and the scrap rate is extremely low. The carpenter carving machine uses a gantry-type structure and a bed of heavy-duty steel structure to ensure the overall stability of the machine. The rack drive makes the transmission smooth, ensuring long-term high-speed operation without deformation and no vibration. In this way, when the precision wooden door is carved, the accuracy and beauty of the carving can be ensured, and then the efficiency of the wooden door manufacturing is greatly improved.

The traditional craft wooden door system has to do many times according to the artificial practice elements, the output value is low, and the cost is high. Now we use the wooden door produced by the carpenter carving machine. The carved picture is more exquisite and suitable for batch production.

With the rapid development of the real estate industry, the demand for high-grade wooden doors has gradually emerged. The use of carpenter carving machine has a good effect on solving this problem. Choosing a good carpenter carving machine is not only satisfactory in terms of use, but also in the manufacturing process of the product. The carpenter carving machine developed by Chengdu Kexing according to the needs of the market is the best choice for all kinds of wooden door carving and milling. The machine has been in the market for two years and has been well received by consumers.

How to maintain the engraving machine daily

In order to help us better extend the life of the engraving machine dust cover, we will introduce the daily maintenance of the engraving machine dust cover today, and we hope to assist us.

1, daily viewing

Excavation of all kinds of chips and other stolen goods in the excavation table, to avoid the accumulation of debris, to see if the running track reaches the smooth requirements, to avoid the damage caused by the huge conflict of insufficient smooth oil, to see if the appearance is very smooth, The presence or absence of scratches, as a basis for detection of early detection, these problems are best repeated before the afternoon of work, these tasks are the main points of the day, expectations to cause our attention.

2. The content of regular inspection is mainly the inspection of the dust cover of the engraving machine to prevent the dust and abrasive particles from sticking to the appearance of the screw. If these things exist, it will affect the service life of the screw and the accuracy of the work, forming the product. If it is unqualified, if the damage of the screw guard cover is found during the inspection, it should be repaired in time, and it should be replaced in time when the damage is severe.


First of all, you should check every day, the shovel excluding the various chips and other stolen goods in the table, to avoid the accumulation of debris, to see if the running track reaches the smooth requirements, to avoid the damage caused by the huge conflict of insufficient smooth oil, look at the appearance Is it very smooth, with or without scratches, as a basis for early detection, these problems are best repeated before the afternoon of work, these are the daily points, expectations to cause our attention.

Secondly, the content of the regular inspection is mainly the inspection of the engraving machine organ dust cover to prevent the dust and abrasive particles from sticking to the outer surface of the cooling pipe. If these things exist, it will affect the service life of the screw and the accuracy of the work, forming the product. If it is unqualified, if the damage of the screw guard cover is found during the inspection, it should be repaired in time, and it should be replaced in time when the damage is severe.

Maintenance is an important method for improving the service life of the machine's dust cover.

1. In normal use, it should be used normally according to the operating standards.

2. Check the water pipe connecting the spindle motor and the water pump, turn on the water pump power supply, and check whether the pump water supply and drainage operation is normal.

3. In order to avoid the abnormality of the power socket or the poor contact, the product will be scrapped. Please choose an excellent power socket and should have a solid grounding protection.

4. Daily protection requires that the work surface and equipment be cleaned up after the completion of daily work to avoid unnecessary losses.

5, timing protection requirements are carried out once a month, the purpose of protection is to check whether the screws in various parts of the machine are loose, to ensure the smooth conditions of the machine and environmental conditions.How to maintain the engraving machine daily

In order to help us better extend the life of the engraving machine dust cover, we will introduce the daily maintenance of the engraving machine dust cover today, and we hope to assist us.

1, daily viewing

Excavation of all kinds of chips and other stolen goods in the excavation table, to avoid the accumulation of debris, to see if the running track reaches the smooth requirements, to avoid the damage caused by the huge conflict of insufficient smooth oil, to see if the appearance is very smooth, The presence or absence of scratches, as a basis for detection of early detection, these problems are best repeated before the afternoon of work, these tasks are the main points of the day, expectations to cause our attention.

2. The content of regular inspection is mainly the inspection of the dust cover of the engraving machine to prevent the dust and abrasive particles from sticking to the appearance of the screw. If these things exist, it will affect the service life of the screw and the accuracy of the work, forming the product. If it is unqualified, if the damage of the screw guard cover is found during the inspection, it should be repaired in time, and it should be replaced in time when the damage is severe.


First of all, you should check every day, the shovel excluding the various chips and other stolen goods in the table, to avoid the accumulation of debris, to see if the running track reaches the smooth requirements, to avoid the damage caused by the huge conflict of insufficient smooth oil, look at the appearance Is it very smooth, with or without scratches, as a basis for early detection, these problems are best repeated before the afternoon of work, these are the daily points, expectations to cause our attention.

Secondly, the content of the regular inspection is mainly the inspection of the engraving machine organ dust cover to prevent the dust and abrasive particles from sticking to the outer surface of the cooling pipe. If these things exist, it will affect the service life of the screw and the accuracy of the work, forming the product. If it is unqualified, if the damage of the screw guard cover is found during the inspection, it should be repaired in time, and it should be replaced in time when the damage is severe.

Maintenance is an important method for improving the service life of the machine's dust cover.

1. In normal use, it should be used normally according to the operating standards.

2. Check the water pipe connecting the spindle motor and the water pump, turn on the water pump power supply, and check whether the pump water supply and drainage operation is normal.

3. In order to avoid the abnormality of the power socket or the poor contact, the product will be scrapped. Please choose an excellent power socket and should have a solid grounding protection.

4. Daily protection requires that the work surface and equipment be cleaned up after the completion of daily work to avoid unnecessary losses.

5, timing protection requirements are carried out once a month, the purpose of protection is to check whether the screws in various parts of the machine are loose, to ensure the smooth conditions of the machine and environmental conditions.